WiMAX

WiMax, also known as 802.16, looks to combine the benefits of broadband and wireless. WiMax will provide high-speed wireless Internet over very long distances and will most likely provide access to large areas such as cities. WiMax technology will be available in most American cities in 2008.

WiMAX
by Ed Grabianowski and Marshall Brain, Howstuffworks

Introduction to How WiMAX Works

Think about how you access the Internet today. There are basically three different options:

Broadband access - In your home, you have either a DSL or cable modem. At the office, your company may be using a T1 or a T3 line.

CATV podatkovna povezava

WiFi access - In your home, you may have set up a WiFi router that lets you surf the Web while you lounge with your laptop. On the road, you can find WiFi hot spots in restaurants, hotels, coffee shops and libraries.

Dial-up access - If you are still using dial-up, chances are that either broadband access is not available, or you think that broadband access is too expensive.
The main problems with broadband access are that it is pretty expensive and it doesn't reach all areas. The main problem with WiFi access is that hot spots are very small, so coverage is sparse.

What if there were a new technology that solved all of these problems? This new technology would provide:

The high speed of broadband service
Wireless rather than wired access, so it would be a lot less expensive than cable or DSL and much easier to extend to suburban and rural areas
Broad coverage like the cell phone network instead of small WiFi hotspots
This system is actually coming into being right now, and it is called WiMAX. WiMAX is short for Worldwide Interoperability for Microwave Access, and it also goes by the IEEE name 802.16.
WiMAX has the potential to do to broadband Internet access what cell phones have done to phone access. In the same way that many people have given up their "land lines" in favor of cell phones, WiMAX could replace cable and DSL services, providing universal Internet access just about anywhere you go. WiMAX will also be as painless as WiFi -- turning your computer on will automatically connect you to the closest available WiMAX antenna.

In this article, we'll find out how WiMAX works, what engineers are doing to make it better and what it could mean for the future of wireless Internet.

How WiMAX Works

In practical terms, WiMAX would operate similar to WiFi but at higher speeds, over greater distances and for a greater number of users. WiMAX could potentially erase the suburban and rural blackout areas that currently have no broadband Internet access because phone and cable companies have not yet run the necessary wires to those remote locations.
A WiMAX system consists of two parts:

A WiMAX tower, similar in concept to a cell-phone tower - A single WiMAX tower can provide coverage to a very large area -- as big as 3,000 square miles (~8,000 square km).

A WiMAX receiver - The receiver and antenna could be a small box or PCMCIA card, or they could be built into a laptop the way WiFi access is today.
A WiMAX tower station can connect directly to the Internet using a high-bandwidth, wired connection (for example, a T3 line). It can also connect to another WiMAX tower using a line-of-sight, microwave link. This connection to a second tower (often referred to as a backhaul), along with the ability of a single tower to cover up to 3,000 square miles, is what allows WiMAX to provide coverage to remote rural areas.

What this points out is that WiMAX actually can provide two forms of wireless service:

• There is the non-line-of-sight, WiFi sort of service, where a small antenna on your computer connects to the tower. In this mode, WiMAX uses a lower frequency range -- 2 GHz to 11 GHz (similar to WiFi). Lower-wavelength transmissions are not as easily disrupted by physical obstructions -- they are better able to diffract, or bend, around obstacles.
• There is line-of-sight service, where a fixed dish antenna points straight at the WiMAX tower from a rooftop or pole. The line-of-sight connection is stronger and more stable, so it's able to send a lot of data with fewer errors. Line-of-sight transmissions use higher frequencies, with ranges reaching a possible 66 GHz. At higher frequencies, there is less interference and lots more bandwidth.

WiFi-style access will be limited to a 4-to-6 mile radius (perhaps 25 square miles or 65 square km of coverage, which is similar in range to a cell-phone zone). Through the stronger line-of-sight antennas, the WiMAX transmitting station would send data to WiMAX-enabled computers or routers set up within the transmitter's 30-mile radius (2,800 square miles or 9,300 square km of coverage). This is what allows WiMAX to achieve its maximum range.

What Can WiMAX Do?

WiMAX operates on the same general principles as WiFi -- it sends data from one computer to another via radio signals. A computer (either a desktop or a laptop) equipped with WiMAX would receive data from the WiMAX transmitting station, probably using encrypted data keys to prevent unauthorized users from stealing access.

The fastest WiFi connection can transmit up to 54 megabits per second under optimal conditions. WiMAX should be able to handle up to 70 megabits per second. Even once that 70 megabits is split up between several dozen businesses or a few hundred home users, it will provide at least the equivalent of cable-modem transfer rates to each user.

The biggest difference isn't speed; it's distance. WiMAX outdistances WiFi by miles. WiFi's range is about 100 feet (30 m). WiMAX will blanket a radius of 30 miles (50 km) with wireless access. The increased range is due to the frequencies used and the power of the transmitter. Of course, at that distance, terrain, weather and large buildings will act to reduce the maximum range in some circumstances, but the potential is there to cover huge tracts of land.

IEEE 802.16 Specifications

• Range - 30-mile (50-km) radius from base station
• Speed - 70 megabits per second
• Line-of-sight not needed between user and base station
• Frequency bands - 2 to 11 GHz and 10 to 66 GHz (licensed and unlicensed bands)
• Defines both the MAC and PHY layers and allows multiple PHY-layer specifications (See How OSI Works)

Dollars and Cents

A citywide blanket coverage of wireless Internet access sounds great, but companies aren't going to go around setting up WiMAX base stations out of sheer kindness. Who's going to pay for WiMAX?
It depends how it will be used. There are two ways WiMAX can be implemented -- as a zone for wireless connections that single users go to when they want to connect to the Internet on a laptop (the non-line-of-sight "super WiFi" implementation), or as a line-of-sight hub used to connect hundreds of customers to a steady, always-on, high-speed wireless Internet connection.

Under the "super WiFi" plan, cities might pay to have WiMAX base stations set up in key areas for business and commerce and then allow people to use them for free. They already do this with WiFi, but instead of putting in a bunch of WiFi hot spots that cover a few hundred square yards, a city could pay for one WiMAX base station and cover an entire financial district. This could provide a strong draw when city leaders try to attract businesses to their area.

Some companies might set up WiMAX transmitters and then make people pay for access. Again, this is similar to strategies used for WiFi, but a much wider area would be covered. Instead of hopping from one hot spot to another, WiMAX-enabled users could have Internet access anywhere within 30 miles of the WiMAX base station. These companies might offer unlimited access for a monthly fee or a "pay as you go" plan that charges on a per-minute or per-hour basis.

The high-speed wireless hub plan has the potential to be far more revolutionary. If you have high-speed Internet access now, it probably works something like this: The cable (or phone) company has a line that runs into your home. That line goes to a cable modem, and another line runs from the modem to your computer. If you have a home network, first it goes to a router and then on to the other computers on the network. You pay the cable company a monthly fee, which reflects in part the expense of running cable lines to every single home in the neighborhood.

On the next page, we'll discuss how WiMAX can work for you

The WiMAX Scenario

Here's what would happen if you got WiMAX. An Internet service provider sets up a WiMAX base station 10 miles from your home. You would buy a WiMAX-enabled computer (some of them should be on store shelves in 2005) or upgrade your old computer to add WiMAX capability. You would receive a special encryption code that would give you access to the base station. The base station would beam data from the Internet to your computer (at speeds potentially higher than today's cable modems), for which you would pay the provider a monthly fee. The cost for this service could be much lower than current high-speed Internet-subscription fees because the provider never had to run cables.

The WiMAX Scenario

Here's what would happen if you got WiMAX. An Internet service provider sets up a WiMAX base station 10 miles from your home. You would buy a WiMAX-enabled computer (some of them should be on store shelves in 2005) or upgrade your old computer to add WiMAX capability. You would receive a special encryption code that would give you access to the base station. The base station would beam data from the Internet to your computer (at speeds potentially higher than today's cable modems), for which you would pay the provider a monthly fee. The cost for this service could be much lower than current high-speed Internet-subscription fees because the provider never had to run cables.

If you have a home network, things wouldn't change much. The WiMAX base station would send data to a WiMAX-enabled router, which would then send the data to the different computers on your network. You could even combine WiFi with WiMAX by having the router send the data to the computers via WiFi.

WiMAX doesn't just pose a threat to providers of DSL and cable-modem service. The WiMAX protocol is designed to accommodate several different methods of data transmission, one of which is Voice Over Internet Protocol (VoIP). VoIP allows people to make local, long-distance and even international calls through a broadband Internet connection, bypassing phone companies entirely. If WiMAX-compatible computers become very common, the use of VoIP could increase dramatically. Almost anyone with a laptop could make VoIP calls.

For more information on WiMAX, wireless networking and related topics, check out the links on the next page.

 

Vsak izmed TV–kanalov, ki ga sprejmemo preko kabla, je izoliran signal in vsi signali prispejo hkrati. S tem da posvetijo nekaj širokopasovnega prenosa za prenos podatkov, CATV ponudniki lahko dostavijo internetne podatke istočasno kot televizijske signale. Če že imamo kabelsko TV, je namestitev dostopa do interneta odvisna od namestitve razdelilnika na kabel in priključitve na napravo, ki ji rečemo (seveda napačno) kabelski modem in je povezan z eternetnim vmesnikom v računalniku.

WiMAX 2.različica

By Wikipedia

 

WiMAX, the Worldwide Interoperability for Microwave Access, is a telecommunications technology aimed at providing wireless data over long distances in a variety of ways, from point-to-point links to full mobile cellular type access. It is based on the IEEE 802.16 standard, which is also called WirelessMAN. The name WiMAX was created by the WiMAX Forum, which was formed in June 2001 to promote conformance and interoperability of the standard. The forum describes WiMAX as "a standards-based technology enabling the delivery of last mile wireless broadband access as an alternative to cable and DSL."

802.16d

Strictly speaking, 802.16d has never existed as a standard. The standard is correctly called 802.16-2004 and was developed by the IEEE 802.16 Task Group d. Therefore the project was called 802.16d, but the standard never was. However, since this standard is frequently called 802.16d, that term is also used in this article to assist readability.

802.16e

Just as 802.16d has never existed as a standard, neither has 802.16e. 802.16e is an amendment to 802.16-2004, and the amendment is properly referred to as 802.16e-2005. 802.16e-2005 is not a standard in its own right - since it is only an amendment, the original document (802.16-2004) has to be read and then the amendments added to it.

Fixed WiMAX

This is a phrase frequently used to refer to systems built using 802.16-2004 ('802.16d') and the OFDM PHY as the air interface technology.

Fixed WiMAX deployments do not cater for handoff between Base Stations, therefore the service provider cannot offer mobility.

Mobile WiMAX

A phrase frequently used to refer to systems built using 802.16e-2005 and the OFDMA PHY as the air interface technology. "Mobile WiMAX" implementations can be used to deliver both fixed and mobile services.

Uses

The bandwidth and reach of WiMAX make it suitable for the following potential applications:

Connecting Wi-Fi hotspots with each other and to other parts of the Internet.
Providing a wireless alternative to cable and DSL for last mile broadband access.
Providing high-speed data and telecommunications services.
Providing a diverse source of Internet connectivity as part of a business continuity plan. That is, if a business has a fixed and a wireless Internet connection, especially from unrelated providers, they are unlikely to be affected by the same service outage.
Providing nomadic connectivity.

Broadband access

Many companies are closely examining WiMAX for "last mile" connectivity at high data rates. The resulting competition may bring lower pricing for both home and business customers or bring broadband access to places where it has been economically unavailable. Prior to WiMAX, many operators have been using proprietary fixed wireless technologies for broadband services.

WiMAX access was used to assist with communications in Aceh, Indonesia, after the tsunami in December 2004. All communication infrastructure in the area, other than Ham Radio, was destroyed, making the survivors unable to communicate with people outside the disaster area and vice versa. WiMAX provided broadband access that helped regenerate communication to and from Aceh.

WiMAX was used by Intel to assist the FCC and FEMA in their communications efforts in the areas affected by Hurricane Katrina. [1]

Subscriber units

WiMAX subscriber units are available in both indoor and outdoor versions from several manufacturers. Self-install indoor units are convenient, but radio losses mean that the subscriber must be significantly closer to the WiMAX base station than with professionally-installed external units. As such, indoor-installed units require a much higher infrastructure investment as well as operational cost (site lease, backhaul, maintenance) due to the high number of base stations required to cover a given area. Indoor units are comparable in size to a cable modem or DSL modem. Outdoor units are roughly the size of a laptop PC, and their installation is comparable to a residential satellite dish.

With the advent of mobile WiMAX, there is an increasing focus on portable units. This includes handsets (similar to cellular smartphones) and PC peripherals (PC Cards or USB dongles). In addition, there is much emphasis from operators on consumer electronics devices (games terminals, MP3 players and the like); it is notable this is more similar to WiFi than 3G cellular technologies.

Mobile applications

Some cellular companies are evaluating WiMAX as a means of increasing bandwidth for a variety of data-intensive applications; Sprint Nextel announced in mid-2006 that it would invest about US$ 5 billion in a WiMAX technology buildout over the next few years.[2] As of Friday, November 9, 2007, this project in partnership with Clearwire has been shelved, but the project could be revived with or without Clearwire once Sprint hires a new CEO. On December 5, 2007, Bin Shen, Sprint's VP of Product Management and Partnership Development, announced that Sprint's WiMAX network will go live in a soft launch in Chicago, Baltimore, and Washington DC. Full commercial launch is still expected to be approximately spring of 2008.[3] In December 2007 Wateen Telecom Pakistan deployed the largest and the first in the world to roll-out WiMAX 802.16e network in 22 cities of Pakistan. In line with these possible applications is the technology's ability to serve as a high bandwidth "backhaul" for Internet or cellular phone traffic from remote areas back to an Internet backbone. Although the cost per user/point of WiMAX in a remote application will be higher, it is not limited to such applications, and may be an answer to reducing the cost of T1/E1 backhaul as well. Given the limited wired infrastructure in some developing countries, the costs to install a WiMAX station in conjunction with an existing cellular tower or even as a solitary hub are likely to be small in comparison to developing a wired solution. Areas of low population density and flat terrain are particularly suited to WiMAX and its range. For countries that have skipped wired infrastructure as a result of prohibitive costs and unsympathetic geography, WiMAX can enhance wireless infrastructure in an inexpensive, decentralized, deployment-friendly and effective manner.

Technical information

WiMAX is a term coined to describe standard, interoperable implementations of IEEE 802.16 wireless networks, similar to the way the term Wi-Fi is used for interoperable implementations of the IEEE 802.11 Wireless LAN standard. However, WiMAX is very different from Wi-Fi in the way it works.

MAC layer/data link layer

In Wi-Fi the media access controller (MAC) uses contention access — all subscriber stations that wish to pass data through a wireless access point (AP) are competing for the AP's attention on a random interrupt basis. This can cause subscriber stations distant from the AP to be repeatedly interrupted by closer stations, greatly reducing their throughput. This makes services such as Voice over IP (VoIP) or IPTV, which depend on an essentially-constant Quality of Service (QoS) depending on data rate and interruptibility, difficult to maintain for more than a few simultaneous users.

In contrast, the 802.16 MAC uses a scheduling algorithm for which the subscriber station need compete once (for initial entry into the network). After that it is allocated an access slot by the base station. The time slot can enlarge and contract, but remains assigned to the subscriber station, which means that other subscribers cannot use it. In addition to being stable under overload and over-subscription (unlike 802.11), the 802.16 scheduling algorithm can also be more bandwidth efficient. The scheduling algorithm also allows the base station to control QoS parameters by balancing the time-slot assignments among the application needs of the subscriber stations.

Physical layer

The original WiMAX standard (IEEE 802.16) specified WiMAX for the 10 to 66 GHz range. 802.16a, updated in 2004 to 802.16-2004, added specifications for the 2 to 11 GHz range. 802.16-2004 was updated to 802.16e in 2005 and uses scalable orthogonal frequency-division multiple access (SOFDMA) as opposed to the OFDM version with 256 sub-carriers (of which 200 are used) in 802.16d. More advanced versions, including 802.16e, also bring Multiple Antenna Support through Multiple-input multiple-output communications (MIMO) See WiMAX MIMO. This brings potential benefits in terms of coverage, self installation, power consumption, frequency re-use and bandwidth efficiency. 802.16e also adds a capability for full mobility support. The WiMAX certification allows vendors with 802.16d products to sell their equipment as WiMAX certified, thus ensuring a level of interoperability with other certified products, as long as they fit the same profile.

Most commercial interest is in the 802.16d and .16e standards, since the lower frequencies used in these variants suffer less from inherent signal attenuation and therefore give improved range and in-building penetration. Already today, a number of networks throughout the world are in commercial operation using certified WiMAX equipment compliant with the 802.16d standard.

Architecture

The WiMAX Forum has defined an architecture that defines how a WiMAX network connects with other networks, and a variety of other aspects of operating such a network, including address allocation, authentication, etc. An overview of the architecture is given in the illustration. This defines the following components:

SS/MS: the Subscriber Station/Mobile Station
ASN: the Access Service Network
BS: Base station, belongs to ASN
ASN-GW: belongs to ASN
CSN: the Connectivity Service Network
HA: Home Agent, belongs to CSN
AAA: AAA Server, belongs to CSN
NAP: a Network Access Provider
NSP: a Network Service Provider
plus a number of interconnections (or reference points) between these, labeled R1 to R5 and R8.

It's important to note that the functional architecture can be designed into various hardware configurations rather than fixed configurations. For example, the architecture is flexible to allow various scale and functionality of remote/mobile stations and collaborative aggregations of femto, pico, and mini RS/MS.

Comparison with Wi-Fi

Possibly due to the fact both WiMAX and Wi-Fi begin with the same two letters, are based upon IEEE standards beginning with "802.", and both have a connection to wireless connectivity and the Internet, comparisons and confusion between the two are frequent. Despite this, the two standards are aimed at different applications.

WiMAX is a long-range system, covering many kilometers that typically uses licensed spectrum (although it is also possible to use unlicensed spectrum) to deliver a point-to-point connection to the Internet from an ISP to an end user. Different 802.16 standards provide different types of access, from mobile (analogous to access via a cellphone) to fixed (an alternative to wired access, where the end user's wireless termination point is fixed in location.)

Wi-Fi is a shorter range system, typically hundreds of meters, that uses unlicensed spectrum to provide access to a network, typically covering only the network operator's own property. Typically Wi-Fi is used by an end user to access their own network, which may or may not be connected to the Internet. If WiMAX provides services analogous to a cellphone, Wi-Fi is more analogous to a cordless phone.

WiMAX and Wi-Fi have quite different Quality of Service (QoS) mechanisms. WiMAX uses a mechanism based on setting up connections between the Base Station and the user device. Each connection is based on specific scheduling algorithms, which means that QoS parameters can be guaranteed for each flow. WiFi has introduced a QoS mechanism similar to fixed Eternet, where packets can receive different priorities based on their tags. This means that QoS is relative between packets/flows, as opposed to guaranteed.

WiMAX is highly scalable from what are called "femto"-scale remote stations to multi-sector 'maxi' scale base that handle complex tasks of management and mobile handoff functions and include MIMO-AAS smart antenna subsystems.

Due to the ease and low cost with which Wi-Fi can be deployed, it is sometimes used to provide Internet access to third parties within a single room or building available to the provider, often informally, and sometimes as part of a business relationship. For example, many coffee shops, hotels, and transportation hubs contain Wi-Fi access points providing access to the Internet for customers.

Spectrum allocation issues
The 802.16 specification applies across a wide swath of the RF spectrum, and WiMAX could function on any frequency below 66GHz"IEEE Standard for Local and metropolitan area networks Part 16: Air Interface for Fixed and Mobile Broadband Wireless Access Systems Amendment 2: Physical and Medium Access Control Layers for Combined Fixed and Mobile Operation in Licensed Bands and Corrigendum 1," IEEE Std 802.16e-2005 and IEEE Std 802.16-2004/Cor 1-2005 (Amendment and Corrigendum to IEEE Std 802.16-2004), 2006, pp. 3, (higher frequencies would decrease the range of a Base Station to a few hundred meters in an urban environment).

There is no uniform global licensed spectrum for WiMAX, although the WiMAX Forum has published three licensed spectrum profiles: 2.3GHz, 2.5GHz and 3.5GHz, in an effort to decrease cost: economies of scale dictate that the more WiMAX embedded devices (such as mobile phones and WiMAX-embedded laptops) are produced, the lower the unit cost. (The two highest cost components of producing a mobile phone are the silicon and the extra radio needed for each band.) Similar economy of scale benefits apply to the production of Base Stations.

In the unlicensed band, 5.x GHz is the approved profile. Telecom companies are unlikely to use this spectrum widely other than for backhaul, as they do not own and control the spectrum.

In the USA, the biggest segment available is around 2.5 GHz,[4] and is already assigned, primarily to Sprint Nextel and Clearwire. Elsewhere in the world, the most-likely bands used will be the Forum approved ones, with 2.3 GHz probably being most important in Asia. Some countries in Asia like India, Vietnam and Indonesia will use a mix of 3.3 GHz and other frequencies.

Analog TV bands (700MHz) may become available for WiMAX use, but await the complete rollout of digital TV, and there will be other uses suggested for that spectrum. In the USA the FCC auction for this spectrum is scheduled for January 2008 [2]. EU commissioner Viviane Reding has suggested re-allocation of 500-800 MHz spectrum for wireless communication, including WiMAX [3].

WiMAX profiles define channel size, TDD/FDD and other necessary attributes in order to have inter-operating products. The current fixed profiles are defined for both TDD and FDD profiles. At this point, all of the mobile profiles are TDD only. The fixed profiles have channel sizes of 3.5 MHz, 5 MHz, 7 MHz and 10 MHz. The mobile profiles are 5 MHz, 8.75 MHz and 10 MHz. (Note: the 802.16 standard allows a far wider variety of channels, but only the above subsets are supported as WiMAX profiles).

Since October 2007, the Radiocommunication Sector of the International Telecommunication Union (ITU-R) has decided to include WiMAX technology in the IMT-2000 set of standards. This enables spectrum owners (specifically in the 2.5-2.69GHz band at this stage) to use Mobile WiMAX equipment in any country that recognizes the IMT-2000.

Spectral Efficiency
One of the significant advantages of advanced wireless systems such as WiMAX is spectral efficiency. For example, 802.16-2004 (fixed) has a spectral efficiency of 3.7 bit/s/Hertz, and other 3.5-4G wireless systems offer spectral efficiencies that are similar to within a few tenths of a percent. The notable advantage of WiMAX comes from combining SOFDMA with smart antenna technologies. This multiplies the effective spectral efficiency through multiple reuse and smart network deployment topologies. The direct use of frequency domain organization simplifies designs using MIMO-AAS compared to CDMA/WCDMA methods, resulting in more-effective systems.[citation needed]

Limitations
A commonly-held misconception is that WiMAX will deliver 70 Mbit/s over 50 kilometers. In reality, WiMAX can do one or the other - operating over maximum range (50 km) increases bit error rate and thus must use a lower bitrate. Lowering the range allows a device to operate at higher bitrates.

Typically, fixed WiMAX networks have a higher-gain directional antenna installed near the client (customer) which results in greatly increased range and throughput. Mobile WiMAX networks are usually made of indoor "customer premises equipment" (CPE) such as desktop modems, laptops with integrated Mobile WiMAX or other Mobile WiMAX devices. Mobile WiMAX devices typically have an omni-directional antenna which is of lower-gain compared to directional antennas but are more portable. In practice, this means that in a line-of-sight environment with a portable Mobile WiMAX CPE, speeds of 10 Mbit/s at 10 km could be delivered However, in urban environments they may not have line-of-sight and therefore users may only receive 10 Mbit/s over 2 km. Higher-gain directional antennas can be used with a Mobile WiMAX network with range and throughput benefits but the obvious loss of practical mobility.

Like most wireless systems, available bandwidth is shared between users in a given radio sector, so performance could deteriorate in the case of many active users in a single sector. In practice, many users will have a range of 2-, 4-, 6-, 8-, 10- or 12 Mbit/s services and additional radio cards will be added to the base station to increase the capacity as required.

Because of this, various granular and distributed network architectures are being incorporated into WiMAX through independent development and within the 802.16j mobile multi-hop relay (MMR) task group. This includes wireless mesh, grids, network remote station repeaters which can extend networks and connect to backhaul.

Silicon implementations

A critical requirement for the success of a new technology is the availability of low-cost chipsets and silicon implementations.

Intel is a leader in promoting WiMAX, and has developed its own chipset. However, it is notable that most of the major semiconductor companies have to date been more cautious of involvement and most of the solutions come from specialist smaller or start-up suppliers. For the client-side these include GCT, Altair, Beceem, GCI, Runcom, Motorola with TI, NextWave, Sequans, Redpine signals[4] and a number of others. Both Sequans and Wavesat manufacture solutions for both clients and network while TI, DesignArt, and picoChip are focused on WiMAX chipsets for basestations.

Standards

The current WiMAX incarnation, Mobile WiMAX, is based upon IEEE Std 802.16e-2005,[5] approved in December 2005. It is an amendment of IEEE Std 802.16-2004[6] and so the actual standard is 802.16-2004 as amended by 802.16e-2005 - the specifications need to be read together to understand them.

IEEE Std 802.16-2004 addresses only fixed systems. It replaced IEEE Standards 802.16-2001, 802.16c-2002, and 802.16a-2003.

IEEE 802.16e-2005

IEEE 802.16e-2005 improves upon IEEE 802.16-2004 by:

Adding support for mobility (soft and hard handover between base stations). This is seen as one of the most important aspects of 802.16e-2005, and is the very basis of 'Mobile WiMAX'.
Scaling of the Fast Fourier Transform (FFT) to the channel bandwidth in order to keep the carrier spacing constant across different channel bandwidths (1.25-20 MHz). Constant carrier spacing results in a higher spectrum efficiency in wide channels, and a cost reduction in narrow channels. Also known as Scalable OFDMA (SOFDMA).
Improving NLOS coverage by utilizing advanced antenna diversity schemes, and hybrid-Automatic Retransmission Request (HARQ)
Improving capacity and coverage by introducing Adaptive Antenna Systems (AAS) and Multiple Input Multiple Output (MIMO) technology
Increasing system gain by use of denser sub-channelization, thereby improving indoor penetration
Introducing high-performance coding techniques such as Turbo Coding and Low-Density Parity Check (LDPC), enhancing security and NLOS performance
Introducing downlink sub-channelization, allowing administrators to trade coverage for capacity or vice versa

Enhanced Fast Fourier Transform algorithm can tolerate larger delay spreads, increasing resistance to multipath interference

Adding an extra QoS class (enhanced real-time Polling Service) more appropriate for VoIP applications.

802.16d vendors point out that fixed WiMAX offers the benefit of available commercial products and implementations optimized for fixed access. It is a popular standard among alternative service providers and operators in developing areas due to its low cost of deployment and advanced performance in a fixed environment. Fixed WiMAX is also seen as a potential standard for backhaul of wireless base stations such as cellular, WiFi or even Mobile WiMAX.

SOFDMA (used in 802.16e-2005) and OFDM256 (802.16d) are not compatible so most equipment will have to be replaced if an operator wants or needs to move to the later standard. However, some manufacturers are planning to provide a migration path for older equipment to SOFDMA compatibility which would ease the transition for those networks which have already made the OFDM256 investment. Intel provides a dual-mode 802.16-2004 802.16-2005 chipset for subscriber units. This affects a relatively small number users and operators.

Associations

WiMAX Forum

The WiMAX Forum is the organization dedicated to certifying the interoperability of WiMAX products. Those that pass conformance and interoperability testing achieve the "WiMAX Forum Certified" designation and can display this mark on their products and marketing materials. Some vendors claim that their equipment is "WiMAX-ready", "WiMAX-compliant", or "pre-WiMAX", if they are not officially WiMAX Forum Certified.[7]

WiMAX Spectrum Owners Alliance - WiSOA

WiSOA is the first global organization composed exclusively of owners of WiMAX spectrum with plans to deploy WiMAX technology in those bands. WiSOA is focussed on the regulation, commercialisation, and deployment of WiMAX spectrum in the 2.3–2.5 GHz and the 3.4–3.5 GHz ranges. WiSOA are dedicated to educating and informing its members, industry representatives and government regulators of the importance of WiMAX spectrum, its use, and the potential for WiMAX to revolutionise broadband.[8]

Competing technologies

Within the marketplace, WiMAX's main competition comes from existing widely deployed wireless systems such as UMTS and CDMA2000, as well as a number of Internet oriented systems such as HIPERMAN and WiBro.

3G and 4G cellular phone Systems
Both major 3G systems, CDMA2000 and UMTS, compete with WiMAX. Both aim to offer DSL-class Internet access in addition to phone service. UMTS has also been enhanced to compete directly with WiMAX in the form of UMTS-TDD, which can use WiMAX oriented spectrum and provides a more consistent, if lower bandwidth at peak, user experience than WiMAX.

3G cellular phone systems usually benefit from already having entrenched infrastructure, being upgraded from earlier systems. Users can usually fall back to older systems when they move out of range of upgraded equipment, often relatively seamlessly.

The major cellular standards are being evolved to so-called 4G, high bandwidth, low latency, all-IP networks with voice services built on top. With GSM/UMTS, the move to 4G is the 3GPP Long Term Evolution effort. For AMPS/TIA derived standards such as CDMA2000, a replacement called Ultra Mobile Broadband is under development. In both cases, existing air interfaces are being discarded, in favour of OFDMA for the downlink and a variety of OFDM based solutions for the uplink, much akin to WiMAX.

In some areas of the world the wide availability of UMTS and a general desire for standardization has meant spectrum has not been allocated for WiMAX: in July 2005, the EU-wide frequency allocation for WiMAX was blocked.

Mobile Broadband Wireless Access

Mobile Broadband Wireless Access (MBWA) is a technology being developed by IEEE 802.20 and is aimed at wireless mobile broadband for operations from 120 to 350 km/h. The 802.20 standard committee was first to define many of the methods which were later funneled into Mobile WiMAX, including high speed dynamic modulation and similar scalable OFDMA capabilities. It apparently retains fast hand-off, Forward Error Correction (FEC) and cell edge enhancements.

The Working Group was temporarily suspended in mid 2006 by the IEEE-SA Standards Board since it had been the subject of a number of appeals, and a preliminary investigation of one of these "revealed a lack of transparency, possible 'dominance,' and other irregularities in the Working Group".[9]

In September 2006 the IEEE-SA Standards Board approved a plan to enable the working group to continue under new conditions, and the standard is now expected to be finalized by Q2 2008.

Internet-oriented systems

Early WirelessMAN standards, the European standard HIPERMAN and Korean standard WiBro have been harmonized as part of WiMAX and are no longer seen as competition but as complementary. All networks now being deployed in South Korea, the home of the Wibro standard, are now WiMAX.

As a short-range mobile Internet solution, such as in cafes and at transportation hubs like airports, the popular Wi-Fi 802.11b/g system is widely deployed, and provides enough coverage for some users to feel subscription to a WiMAX service is unnecessary.

Future development
Mobile WiMAX based upon 802.16e-2005 has been accepted as IP-OFDMA for inclusion as the sixth wireless link system under IMT-2000. This can hasten acceptance by regulatory authorities and operators for use in cellular spectrum. WiMAX II, 802.16m will be proposed for IMT-Advanced 4G.

The goal for the long term evolution of both WiMAX and LTE is to achieve 100 Mbit/s mobile and 1 Gbit/s fixed-nomadic bandwidth as set by ITU for 4G NGMN (Next Generation Mobile Network) systems through the adaptive use of MIMO-AAS and smart, granular network topologies. 3GPP LTE and WiMAX-m are concentrating much effort on MIMO-AAS, mobile multi-hop relay networking and related developments needed to deliver 10X and higher Co-Channel reuse multiples.

Since the evolution of core air-link technologies has approached the practical limits imposed by Shannon's Theorem, the evolution of wireless has embarked on pursuit of the 3X to 10X+ greater bandwidth and network efficiency gains that are expected by advances in the spatial and smart wireless broadband networking technologies. What will clearly define 4G more than either WCDMA or OFDMA wireless link methods will be wireless networks that more effectively adapt to and take advantage of available spectrum.